Skip to main content
skill CX Codex

moving-target-control — Claude Code skill: what it does

The moving-target-control Claude Code skill plans contact with moving physical objects and checks whether a grasp holds. It activates when a target or receiver may move during approach or transfer.

MIT ★ 488 updated 2026-11-15

Install into Claude Code · Skills CLI (Vercel) All methods and platforms ↓
npx skills add Open-RUA/uni-robot-agent --skill moving-target-control -a claude-code
Open on GitHub

What moving-target-control does

The skill plans a grasp around observed motion, then checks the result. It compares observations with their capture times or environment steps to estimate direction and local speed. From there, it selects a reachable contact area and accounts for the target's movement during approach and gripper closure. It also checks finger clearance and the target's drift through the closing area.

Geometry needs a fresh update near contact; a long chase based on an old position can miss. After closure, the skill checks how the object moves relative to the hand and can use a short lift when appropriate. If the object slips or the receiver moves, it revises the grasp or transfer plan. It does not assume speed stays constant after a disturbance.

What it helps with

  • estimate a target's direction and local speed from observations
  • choose a reachable contact area while accounting for delay
  • check whether a closed gripper holds the object
  • revise a transfer plan after the receiver moves

Example prompts for the agent

  • Grasp the moving object using fresh observations near contact.
  • Check whether the object stays attached after closure and a short lift.
  • Revise the transfer plan because the receiver moved while the hand pursued the target.

How to install moving-target-control

1Skills CLI (Vercel)

npx skills add Open-RUA/uni-robot-agent --skill moving-target-control -a claude-code

2Manually: put the files in place

~/.claude/skills/moving-target-control/SKILL.md

Copy the whole skill folder; for one project use .claude/skills/moving-target-control/

Step by step, with commands for each platform: How to install skills in Claude Code: five ways

Questions about moving-target-control

How do I install moving-target-control in Claude Code?

Run npx skills add Open-RUA/uni-robot-agent --skill moving-target-control -a claude-code. The skill file is located at ~/.claude/skills/moving-target-control/SKILL.md.

What does moving-target-control do?

It plans contact with a moving object using observed motion and fresh geometry, then helps distinguish a miss, a successful grasp, and a later slip.

How does the skill verify a grasp?

It checks the completed closure and, when appropriate, a short lift. A centered wrist image or blocked fingers alone do not confirm that the object was captured.

Source text

SKILL.md · MIT
---
name: moving-target-control
description: Capture or interact with a moving physical target using fresh geometry and observed motion. Use when the target or its receiver can move during approach, closure or transfer.
---

# Plan contact against motion, then verify capture

Use `general/gripper/scene-memory/SKILL.md` to preserve identity and reference
images. Recognizing an object does not establish its current contact position.

## Prepare a reachable contact window

Compare observations with their capture time or native step to establish motion
direction and a local speed estimate. Use actual environment advancement: in a
step-driven scene, reasoning time alone need not move the target; in a continuously
advancing scene, account for elapsed time and observation latency. Do not mix
these clocks or assume constant speed after a disturbance.

Choose a reachable contact region and prepare a compatible orientation before
the target arrives when useful. Allow for movement during the executed approach
and closure, not only the displacement between images. Check finger clearance,
solid contact material and relative drift through the closing region. Refresh
geometry near final contact; shorten the segment whose accuracy depends on an
old moving-target position instead of queuing a long stale chase.

Before capture, preserve the receiver and the subsequent transfer route. A
container on moving support may leave reach while the other hand pursues the
target. Use `general/gripper/placement-and-engagement/SKILL.md` for support roles.

## Distinguish a miss, capture and later loss

Inspect the completed closure and, when lifting is appropriate, a short lift.
Compare the target's original support with its motion relative to the hand;
centered wrist imagery or blocked fingers alone do not establish capture.
Use `general/gripper/state-verification/SKILL.md` for unresolved attachment.

After a miss, update identity, current position and reachable contact window.
After slip, reconsider grip geometry and the loaded motion as well as timing;
one successful lift does not establish retention for the whole transfer.
If the receiver moved or was lost, revise the dependent placement plan before
continuing the carry. Wait for a return only when observations or the instruction
support recurrence; do not assume a disappeared target will circulate back.

© Open-RUA · MIT · Open-RUA/uni-robot-agent

Similar skills

All skills for Game dev and 3D: Unity, Unreal, Godot, Blender →

From the same set41

The whole set →
system The system Claude Code prompt guides control of a dual-arm ARX X5 robot in a live RoboDojo episode. The agent consults skills, observes the scene, and checks action results before proceeding. GP ChatGPT ★ 488repo stars robodojo-return-to-start The robodojo-return-to-start Claude Code skill applies RoboDojo’s finishing posture after the general return procedure. It restores used empty arms to their initial poses and checks their clearance from the result. CX Codex +1 ★ 488repo stars deformable-material The deformable-material Claude Code skill moves selected regions of flexible material and checks their shape after release. It applies when deformation makes rigid-object poses or earlier contact coordinates unreliable. CX Codex +1 ★ 488repo stars contents-transfer contents-transfer — a skill for Claude Code that transfers loose contents from a held vessel into a receiver. It tracks outlet alignment, flow, and what remains. CX Codex +1 ★ 488repo stars return-to-start return-to-start — a skill for Claude Code and Codex guides robotic arms back to their measured starting poses. Verifies position and orientation tolerances before ending the movement. CX Codex +1 ★ 488repo stars held-object-geometry The held-object-geometry Claude Code skill locates a held object's relevant feature relative to the hand. It applies to clearance checks, placement, and tool contact during robot motion. CX Codex +1 ★ 488repo stars reachability-and-recovery The reachability-and-recovery Claude Code skill selects an arm, approach, and permitted relay for a complete gripper route. It activates when the destination is hard to reach or an existing route needs reassignment. CX Codex +1 ★ 488repo stars handover The handover Claude Code skill transfers an object held by one robot hand to another. It is triggered for hand-to-hand transfers, not ordinary placement with a single arm. CX Codex +1 ★ 488repo stars

Project sponsors

Companies that keep this analytics open