eda-architect — Claude Code skill: PCB architecture and constraints
eda-architect walks through the early calls on a board design: purpose, power, interfaces, size. Leaves a spec and a constraints file behind.
no license 137 installs ★ 21 updated 2026-01-01
npx skills add l3wi/claude-eda --skill eda-architect -a claude-codeWhat eda-architect does
eda-architect is the opening step of a PCB pipeline. It kicks in when a project lacks docs/project-spec.md and docs/design-constraints.json, then interviews you about what the board must do, where power comes from, which MCU family fits, what interfaces and sensors are needed, how big the board can be and where it will operate. Power rails get a topology call (LDO or buck), the board gets a layer count, and thermal load is estimated before parts are picked.
Two files come out: a readable spec at docs/project-spec.md and machine-readable constraints at docs/design-constraints.json. The reasoning lives in reference/ — decision trees for power topology and layer count, a thermal estimation guide, the constraint schema, project templates. Tools are limited to Read, Write, WebSearch and Glob.
Risky pairings get flagged before you commit. A switching regulator on two layers draws a warning about the ground plane. Fine-pitch parts under 0.5 mm with hand assembly raise a solderability question. Then it points at /eda-source [component-role] for part selection.
What it helps with
- collect board requirements before any part is chosen
- pick LDO or buck topology for each voltage rail
- estimate heat and layer count ahead of routing
- record dimensions, connectors and operating conditions in a spec
- hand machine-readable constraints to the next step
Example prompts for the agent
- Start a new PCB project: ESP32 board powered over USB, I need a spec and constraints.
- Walk me through the power architecture and write the results to
docs/project-spec.md. - Check this architecture for risky combinations before we pick parts.
How to install eda-architect
1Skills CLI (Vercel)
npx skills add l3wi/claude-eda --skill eda-architect -a claude-code2Manually: put the files in place
~/.claude/skills/eda-architect/SKILL.mdCopy the whole skill folder; for one project use .claude/skills/eda-architect/
1Skills CLI (Vercel)
npx skills add l3wi/claude-eda --skill eda-architect -a codex2Manually: put the files in place
.agents/skills/eda-architect/SKILL.mdFor all projects use ~/.agents/skills/
1Skills CLI (Vercel)
npx skills add l3wi/claude-eda --skill eda-architect -a cursor2Manually: put the files in place
.cursor/skills/eda-architect/SKILL.mdCursor also reads .agents/skills/ and .claude/skills/
1GitHub CLI
gh skill install l3wi/claude-eda templates/claude/skills/eda-architect2Manually: put the files in place
.github/skills/eda-architect/SKILL.md1Skills CLI (Vercel)
npx skills add l3wi/claude-eda --skill eda-architect -a gemini-cli2Platform CLI
gemini skills install https://github.com/l3wi/claude-eda --path templates/claude/skills/eda-architectManually: put the files in place
.devin/skills/eda-architect/SKILL.mdThe legacy .windsurf/skills/ path still works
Skills CLI (Vercel)
npx skills add l3wi/claude-eda --skill eda-architect -a opencodeClaude.ai
Zip the folder and upload it in Settings → Capabilities → Skills
Step by step, with commands for each platform: How to install skills in Claude Code: five ways
Questions about eda-architect
How do I install eda-architect in Claude Code?
Run npx skills add l3wi/claude-eda --skill eda-architect -a claude-code. The skill lands at ~/.claude/skills/eda-architect/SKILL.md.
What does eda-architect do?
It interviews you on the early decisions of a board: power, processor, interfaces, stackup, dimensions, manufacturing. Output goes to docs/project-spec.md and docs/design-constraints.json.
What happens if I pick two layers with a switching regulator?
The skill warns that a solid ground plane is hard to get and asks whether to rework the design or accept the risk. Accepting is allowed.