held-object-geometry — скилл для Claude Code: что делает и установка
Скилл held-object-geometry для Claude Code определяет положение нужной части предмета относительно захвата. Включается, когда робот переносит груз, проходит рядом с препятствием или готовится к контакту с инструментом.
MIT ★ 488 обновлён 2026-11-15
npx skills add Open-RUA/uni-robot-agent --skill held-object-geometry -a claude-codeЧто делает held-object-geometry
Скилл помогает планировать движение по фактическому положению удерживаемого предмета: определяет нижний край для проверки зазора, входной конец и ось для соединения или рабочую поверхность для контакта. Он отличает нужную часть объекта от центра захвата и маски изображения.
После поворота предмета связь между захватом и нужной частью пересчитывается; после проскальзывания или повторного захвата её нужно обновить. Для точного контакта учитываются форма груза, пальцы захвата и положение приёмного отверстия. Если отверстие переместилось, его локализуют заново.
Скилл ссылается на general/gripper/grasp-geometry/SKILL.md, general/gripper/contact-effect/SKILL.md и general/gripper/placement-and-engagement/SKILL.md. Скрытая пальцами рабочая часть может выглядеть смещённой, хотя предмет не сел на опору.
Какие задачи решает
- оценить зазор под нижним краем удерживаемого предмета
- совместить входной конец предмета с приёмным отверстием
- спланировать подход и отход с учётом пальцев захвата
- обновить положение предмета после проскальзывания или повторного захвата
Примеры запросов агенту
- Проверь, пройдёт ли нижний угол удерживаемой детали над краем.
- Совмести рабочий конец инструмента с отверстием и учти место для пальцев.
- Предмет повернулся в захвате: пересчитай положение его рабочей поверхности.
Как установить held-object-geometry
1Через Skills CLI (Vercel)
npx skills add Open-RUA/uni-robot-agent --skill held-object-geometry -a claude-code2Вручную: положить файлы
~/.claude/skills/held-object-geometry/SKILL.mdПапка скилла целиком; для одного проекта — .claude/skills/held-object-geometry/
1Через Skills CLI (Vercel)
npx skills add Open-RUA/uni-robot-agent --skill held-object-geometry -a codex2Вручную: положить файлы
.agents/skills/held-object-geometry/SKILL.mdДля всех проектов — ~/.agents/skills/
1Через Skills CLI (Vercel)
npx skills add Open-RUA/uni-robot-agent --skill held-object-geometry -a cursor2Вручную: положить файлы
.cursor/skills/held-object-geometry/SKILL.mdCursor читает и .agents/skills/, и .claude/skills/
1GitHub CLI
gh skill install Open-RUA/uni-robot-agent uni_robot_agent/resources/skills/general/gripper/held-object-geometry2Вручную: положить файлы
.github/skills/held-object-geometry/SKILL.md1Через Skills CLI (Vercel)
npx skills add Open-RUA/uni-robot-agent --skill held-object-geometry -a gemini-cli2Командой платформы
gemini skills install https://github.com/Open-RUA/uni-robot-agent --path uni_robot_agent/resources/skills/general/gripper/held-object-geometryВручную: положить файлы
.devin/skills/held-object-geometry/SKILL.mdСтарый путь .windsurf/skills/ тоже читается
Claude.ai
Упакуйте папку в zip и загрузите в Settings → Capabilities → Skills
По шагам, с командами для каждой платформы: Как установить скилл в Claude Code: пять способов
Вопросы о held-object-geometry
Как установить held-object-geometry в Claude Code?
Выполни npx skills add Open-RUA/uni-robot-agent --skill held-object-geometry -a claude-code. Файл скилла находится по пути ~/.claude/skills/held-object-geometry/SKILL.md.
Что делает held-object-geometry?
Скилл определяет положение важной для следующего действия части предмета относительно захвата. Он помогает учитывать зазоры, выравнивание с отверстием и контакт с рабочей поверхностью.
Что нужно пересчитать после проскальзывания предмета?
Нужно заново определить связь между захватом и той частью предмета, которая важна для следующего точного контакта.
Исходный текст
SKILL.md · MIT
--- name: held-object-geometry description: Locate the bottom, entering end or working feature of a held object relative to the hand. Use when clearance, placement or tool contact depends on the load's actual pose. --- # Plan with the held object's actual features Identify the feature needed for the next operation: the lowest edge for clearance, an entering end and axis for engagement, or a working surface for tool contact. Estimate its relation to the measured hand from a compatible observation. The finger center, mask median and object center are not interchangeable features. Use `general/gripper/grasp-geometry/SKILL.md` to keep the needed feature accessible. ## Preserve only geometry that remains valid A held object can hang tilted or offset even when the hand reaches its requested pose. Inspect its actual bottom, rim, long extent or working end rather than assuming the initial grasp centered it. After reorientation, transform the feature relationship with the new orientation and check that the grip did not shift; a world-axis offset cannot simply be reused after rotation. Slip, regrasp or support transfer invalidates the old hand-to-object relationship. Refresh the affected feature before precise contact. Reuse a confirmed relation through undisturbed motion; do not repeatedly measure the entire object. ## Check both the moving shape and the receiver Plan approach and withdrawal for the whole load and fingers, including edges below or beside the grasp. A hand above a rim does not establish clearance for the lowest corner. Localize the receiving opening or support again if it moved; an accurate held-object offset cannot compensate for a stale destination. Separate hand tracking, retention and effective contact. A working end following the hand establishes control of the tool, not its effect on the target. Use `general/gripper/contact-effect/SKILL.md` for that effect and `general/gripper/placement-and-engagement/SKILL.md` for the resulting relation. When fingers obscure the deciding feature, choose a useful view or a supported release and withdrawal if the operation permits it; an occluded mask can appear smaller or lower without the object having seated. ## Case: the object is already aligned, but the hand looks rotated The object's identifiable face and directed features already satisfy the required world orientation, although the grasp-site yaw is nonzero. Preserve that useful object orientation during transport when the route permits it. Zero grasp-site yaw is not an object-alignment objective; an unnecessary loaded turn can shift the grip and make the remaining route harder. Confirm alignment from distinguishing features, not bbox aspect ratio alone. If rotation is required, choose it from the measured hand-to-object relationship and available clearance, not an assumed centered grip. After slip, regrasp or an unexpected turn, refresh the affected relationship before using the old placement offset. When retention and geometry remain valid, reuse them and inspect the released result without repeating localization at each move. Before precise engagement, compare the actual working feature and its axis with the receiver, then account for the fingers' approach and withdrawal space. Do not translate a receiver coordinate directly into a gripper-center target without the supported hand-to-feature relationship. A tighter motion tolerance cannot repair an incorrect feature offset or stale held orientation.
© Open-RUA · MIT · Open-RUA/uni-robot-agent